Panasonic PT-D9610U Operating Instructions Manual

Panasonic PTD9610U - DLP PROJECTOR Manual Page 1 PROJECTOR POWER SYSTEM SELECTOR STD RGB INPUT1 INPUT2 INPUT3 BRIGHT CONTRAST LENS – + PC- MUTE ON SCREEN NEXT ID SELECT ID ALL 1 2 3 4 5 6 7 8 9 0 MENU ENTER DLP™ based Projector   Commercial Use Models No. PT-D9510UPT-D9610U Read these instructions completely before operating this unit.  TQBJ0084 Operating Instructions ® (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 2 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it willhelp you to get the most performance out of your new product, and that you will be pleased with your PanasonicDLP TM based projector. The serial number of your product may be found on its back. You should note it in the space provided below andretain this booklet in case service is (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 3 3 Product Outline This is a high-luminance DLP TM  based projector which is powered by a single-phase, 3-wire type 200 V – 240 V power supply. It utilizes three RGB DMD TM chips and a high-output xenon lamp. By fitting a projection lens and input module (sold separately) in accordance with the setting-up location and the type of input signal, it can projectimages onto screens from 100 inches (2.5 m) to 600 inc (...)

PTD9610U - DLP PROJECTOR Page 4 Features 4 By attaching different projection lenses (sold separately) that match the requirements of the setting-up location,images of any size between 100 inches (2.5 m) and 600 inches (15 m) with an aspect ratio of 4:3(PT-D9510U),5:4(PT-D9610U) can be projected, depending on the projection distance.  When using the fixed focus lens, theavailable picture size is 100 to 180(PT-D9510U), 100 to 200(PT-D9610U) inch (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 5 5 IMPORTANT SAFETY NOTICE WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain  or moisture. Power Supply: This DLP TM based Projector is designed to operate on 200 V  —  240 V, 50 Hz / 60 Hz AC only. CAUTION:  This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug.Thi (...)

PTD9610U - DLP PROJECTOR Page 6 Precautions with regard to safety 6 Read these operating instructions thoroughly and check all necessary safety precautionswhen setting up the projector in order to avoid accidents. WARNING Setting-up Installation should only be carried out by a qualified technician. • In order to maintain full safety and precision during installation, such work should only be carried out by a qualified technician. At least three p (...)

PTD9610U - DLP PROJECTOR Page 7 7 When using the projector Do not look into the lens while the projector is being used. • Strong light is emitted from the projector‘s lens. If you look directly into this light, it can hurt and damage your eyes. Do not place the projector on top of surfaces which are sloped or unstable. • The projector may fall down or tip over. Do not place any objects on top of the projector. • If water spills onto the pro (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 8 8 Precautions on handling CAUTION Setting-up The following points should always be observed when setting up this projector. A dedicated power supply must be used. • Ask the place of purchase to carry out any electrical work which may be required to provide a 14 A, 200 V - 240 V AC (single phase) power supply for the projector alone to use. Avoid setting up in places which are subject to vibration or shocks. • If (...)

PTD9610U - DLP PROJECTOR Page 9 9 Notes on use In order to get the best picture quality • If outside light or light from indoor lamps is shining onto the screen, the images projected will not have good contrast. Draw curtains or blinds over any windows, turn off any fluorescent lights near the screen and cover anyhighly-reflective floor and wall surfaces with carpet or wallpaper to prevent reflection. Do not touch the surface of the projection le (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 10 10 Name and function of each part 〈Projector〉 POWER buttonThis button is used to turn the projectorpower supply on and off.•This button is enabled while the MAIN POWER switch is ON.   SYSTEM SELECTOR buttonThis button is used to select RGB, RGBREALITY, or YP B P R (YC b C r ) signal or switch between video and digital-serial signal formats. Arrow buttonsThese buttons are used to select andadjust items in (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 11 11 Name and function of each remote control part 〈Remote control unit〉 STD (standard) buttonThis button is used to reset all of the projector adjustment values (BRIGHT,CONTRAST, COLOR, TINT and SHARPNESS) to the default levels which wereset at the time of shipment from the factory. It is pressed after the respectiveadjustment mode screen has been displayed. SYSTEM SELECTOR buttonThis button is used to select RGB (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 12 12 Name and function of each remote control part (continued) 〈Remote control unit〉 TransmitterThis emits the infrared signals which areused to control the projector when the remotecontrol unit is being used as a wireless unit. Wired remote control terminalThis terminal is used to connect theaccessory cable when the remote controlunit is being used as a wired unit. MENU buttonThis button is used to make the MENU (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 13 13 Before using the remote control unit Inserting the batteries • Insert the AA batteries supplied with the remote control unit, making sure that the polarities are correct. • The batteries also need to be inserted when the remote control unit is connected to the projector using the remote control cable. Attaching the strap                       &# (...)

PTD9610U - DLP PROJECTOR Page 14 14 P R O JE C T O R BR IG HT CO NTR AS T POWER INPUT   1 INPUT        2 STD R G B LENS 1 2 3 4 5 6 7 8 0 9 NEXT PIC  MUTE  ID-SELECT ON          SC REE N ID-ALL >PS< SYS TE R SELECTOR INP UT3 EN TER M EN U Accessory remote control cable To REMOTE IN2 IN terminal To remote control  cable terminal [Projector] (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 15 15 Turning the power ON and OFF Always be sure to follow the procedure given below to turn the projector power on and off. 〈Turning the power on 〉 〈 Turning the power off 〉 • The projector will continue to draw approximately 13 W of power when it is in standby mode, even after the cooling fan has stopped. •The lamp cooling fan will continue to operate for approximately five minutes after t (...)

PTD9610U - DLP PROJECTOR Page 16 16 The figure below shows on-screen displays for any desired setting, starting with the MAIN MENU, and ending withits sub-menu. Normal screen LENS LENS FOCUS  :  ＋−LENS   SHIFT : EXIT : MENU POSITION SHIFTSIZEBLKCLOCK PHASEINPUT RESOLUTIONCLAMP POSITIONKEYSTONEEDGE BLENDING MENU : SUB MENU : ENTER EXIT : MENU PICTURE COLOR TEMP : ＊ ＊ ＊ � (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 17 17 The projection lenses and input modules which are available for use with this projector need to be purchasedseparately  and must be installed to the projector before the projector can be used. • Obtain the required projection lenses and input modules beforehand in accordance with the projection distance and the system used. • When installing an optional input module, refer to page 28 for details. In (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 18 18 Setting up the projector Installing to the floor (Including the direct rear-mounting) 1. Installing drawing of the screen and the projector (unit : mm / inches) L : Projection distance between the screen and the center of the front foot of theprojector. A: Distance between the center of the lens and the top of the setting table (including theheight of a foot of the projector) , 288 mm –313 mm (11.5"- 1 (...)

PTD9610U - DLP PROJECTOR Page 19 Installing to the ceiling (Including direct rear-projection) 19 • Using the projector by installing to the ceiling requires an optional ceiling mount bracket (ET-PKD95). For the projection distance (L), refer to the chapter "Projection distance for each projection lens (sold separately)"on pages  20 - 24.For the procedures to install the ceiling mount bracket on the projector and mount the suspension (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 20 20 Projection distance for each projection lens (sold separately) L SH Screen The required projection distance depends on not only the target picture size but also the type of an optional projection lens. Obtain the appropriate projection lens for the installation space by referring to the projection distance for each projection lens shown in the table below and on the next page.  L    : Projection di (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 21 21 2 540 (100") 3 048 (120") 3 810 (150") 4 572 (180") 5 080 (200") 6 350 (250") 7 620 (300") 8 890 (350") 10 160 (400") 11 430 (450") 12 700 (500") 13 970 (550") 1 245 (4'1") 1 494 (4'11") 1 868 (6'2") 2 241 (7'4") 2 491 (8'2") 3 113 (10'3") 3 736 (12'3") 4 358 (14'4") 4 981 (16'4") 5 604 (18'5") 6 226 (20'5") 6 849 (22'6 (...)

PTD9610U - DLP PROJECTOR Page 22 22 Projection distance measurements for PT-D9610U(screen aspect ratio: 16:9) unit: mm (feet/inches) NOTE:• The projection distance listed in the table may have a variation within ± 5 %.• Keystone (trapezoidal distortion) is compensated to be smaller than the screen size. Projection distance measurements for PT-D9610U (screen aspect ratio: 5:4)               (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 23 23 Calculation of the projection distance for each projection lens (for PT-D9610U) If there is no reference made to the require picture size, calculate the projection distance using an expression below after obtaining the diagonal measurement (inch) of the screen you will use. Model No. of projection lensAspect ratio 4:3 16:9 16:9 4:3 4:3 16:9 ET-D95LE5 (1.5 – 2.0 : 1) ET-D95LE6 (2.0 – 2.5 : 1) ET-D95LE7 (2.5 � (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 24 24 Adjusting projector feet [ Side view ] [ Front view ] Adjustable feet The four feet on the bottom of the projector are adjustable for the height ( 0 mm / 0" to 25 mm / 1") and can be used for its adjustment when the installation position is not level. Model No. of projection lensAspect ratio 4:3 16:9 16:9 16:9 4:3 4:3 4:3 16:9 ET-D95LE1 (1.5 — 2.5 : 1) ET-D95LE2 (2.5 — 4.0 : 1) ET- (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 25 25 Setting the projection method The projection method can be set in accordance with the way the projector has been installed. If the projectedpicture is upside-down or back-to-front, change the projection method while referring to illustrations A to D below. Set  the projection method by displaying on-screen displays using the control buttons on the remote control unit or the projector operating panel. Se (...)

PTD9610U - DLP PROJECTOR Page 26 26 Adjusting the lens Adjusting the focus Adjustment procedure Press the LENS button. ... The LENS screen will be displayed.Use the control level buttons ( + and −) to adjust the focus to the correct setting. • Initial pressing of these buttons will allow fine adjustment. Pressing and holding these buttons will allow the slow mode for the first six seconds and then thefast mode.  Press the ME (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 27 27 Adjustment range after lens positioning is as follows: ※The numbers in brackets are the dimensions when the ET-D95LE9 lens is being used. Adjustment range after lens position (optical shift) (0.24H) 0.35H (0.24H) 0.35H (0.38V) 0.5V (0.38V) 0.5V (0.24H) 0.35H (0.24H) 0.35H (0.38V) 0.50V 0.31V (0.38V)(0.24H) 0.29H 0.31H 0.31H 0.50V 0.50V 0.28V 0.22H (0.24H) 0.29H (0.31V) 0.38V (0.38V) 0.50V 0.31H 0.31H 0.50V 0.22 (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 28 28 Obtain the required input modules (sold separately) beforehand in accordance with the system input signal. • Types of input module (sold separately) • Input slot numbers • The signal sources connected to the input modules can each be selected by specifying the respective slot number using the input select buttons on the remote control unit or the projector operating panel.For details on selec (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 29 29 Disconnect the power supply from the projector before installing any of the input modules. Installation procedure Remove the two screws which are holding the slot cover where the input module is to be installed, and thenremove the slot cover.Fit the input module into the slot rails, and then push the input module in until it is seated in the connector, whilebeing careful not to bump any of the module components.T (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 30 30 Connecting the input module signal source When setting up the projector, you will need to connect the signal source to an input module according to the typeof signal being input. RGB signal input module  ET-MD95RGB VGA to BNC adapter cable RGB signal Component signal Video signal input module  ET-MD95VM2 Serial digital input module ET-MD95SD1 TMDS input module ET-MD95T Component signal SD sign (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 31 Connecting the input module signal source Connecting the signal source to the input module for analog RGB signals If using the input module for analog RGB signals in order to connect the projector to a personal computer, you willalso need to use a separate interface (D-SUB  / BNC) cable. 1.Connecting an analog RGB signal source 2.Connecting a component signal source R/P R G/Y R G B H/H·V V B/P B H/H·V V (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 32 32 The table below lists the different types of analog RGB signals that can be input. If a signal which differs greatly from any of the types listed below is input, the picture image may not be displayed correctly, or black background may displayed. Display mode name Signal data No. of dots Horizontal scanning frequency(kHz) Vertical scanning frequency(Hz) VGA400 640×400 24.8 56.4 640×400 31.5 70.1 640×480 31.5 5 (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 33 33 Connecting the signal source to the input module for video signals 1.Connecting a video signal source • Switching between LINE input and Y/C input is carried out by toggling the INPUT button. (Example)  If the ET-MD95VM2 is inserted in slot 1 the selection will change as follows each time the INPUT 1 button on the remote control unit (or the INPUT button on the projector operating panel) is press (...)

PTD9610U - DLP PROJECTOR Page 34 34 Connecting the signal source to the input module for video signals 2.Connecting a component signal source •  For details of composite and component signal switching, see ET-MD95VM2 (sold separately) signal switching on page 41. Luminance signal Y Color difference signal C b Video signal input module (sold separately) ET-MD95VM2 DVD player LINE/Cr IN C/C b   IN LINE OUT Y  IN Video Modul (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 35 35 Connecting the signal source to the input module for TMDS signals • This input module is for use with personal computers which are equipped with a TMDS output connector.• The connector is a MDR 26-pin connector.• The cable used should not be longer than 7 m / 22.96 feet( Recommend length : 5 m / 16.4 feet). If a cable which is longer than 7 m (22.96 feet) is used, signal conditioning amplifie (...)

PTD9610U - DLP PROJECTOR Page 36 36 • Use an input module which correctly matches the input signal type.• The SYSTEM SELECTOR button can be used to toggle between different formats when using input modules that can handle two different signals with different specifications. The current signal format can bechecked by looking at the on-screen display. SD signal SD signal output Serial digital input module(sold separately) IN   OUT (...)

PTD9610U - DLP PROJECTOR Page 37 37 Connecting the signal source to the input module for serial digital signals SD  signal SD signal output (Active through) Serial digital input module(sold separately)   MAIN IN Professional-type digital VCR ET-MD95SD2 (for 480p/480i/576i) 480p Module ET-MD95SD2   SERIAL   MAIN OUT   SUB IN   SUB OUT MAIN (Link-A) SUB (Link-B) MAIN (Link-A) SUB (Link-B) 1. 480p dual link (4:2:2p):  (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 38 38 2. 1) 480p single link (4:2:0p): 59.94 Hz progressive scan with 720 by 483 active lines at 360 Mbps, complying with the SMPTE294M Standard 2) 480i (4:2:2): 59.94 Hz interlace scan with 525 lines at 270 Mbps, complying with the SMPTE294M Standard  3) 576i (4:2:2):  50 Hz interlace scan with 625 lines at 270 Mbps, complying with the SMPTE294M Standard SD signal SD signal output (Active through) Serial dig (...)

PTD9610U - DLP PROJECTOR Page 39 39 Connecting the signal source to the input module for serial digital signals HD SD signal SD signal output (Active through) Serial digital input module(sold separately) IN   OUT Professional-type digital VCR ET-MD95SD3 (for HD SDI) 1080i/720p Module ET-MD95SD3   HD SERIAL    • Use an input module which correctly matches the input signal type.• Input modules that accommodate 8 vide (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 40 40 Selecting the input signal • The following remote control unit buttons and the INPUT button on the projector operating panel can be used to switch between different input sources. • The input source can be changed in the order INPUT 1  INPUT 2  INPUT 3 each time the INPUT button on the projector operating panel is pressed. • When using the video signal input module ( ET-MD95VM2), th (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 41 41 Selecting the signal of ET-MD95VM2(sold separately) When using the projector with the optional ET-MD95VM2 Video Input Module, select the appropriate video signalformat that matches the video equipment you are using. Setting procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP  ( ) and DOWN ( ) arrow buttons to select OPTION. MENU AUTO SETUP LENSPICTUREPOSITIONOPTIONSI (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 42 42 Registering input signal data Because the projector has no factory pre-set data of input signals, be sure to register input signal data before first use. • Up to 64 different input signals can be registered.• Input a signal according to an input module installed on the projector and register the signal data. Registration new signal  • If a new signal is input and MENU key of the rem (...)

PTD9610U - DLP PROJECTOR Page 43 43 When the memory does not allow new signal registration because it is full • When a total of 64 signals has already been registered and the memory is full, inputting a new signal and pressing the MENU button on the remote control unit or the projector operating panel will display the overwriting registration screen below. In this case, to register the new data, an existing signal will be clea (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 44 Sub-memory 44 This equipment has a sub memory function which enables storage of multiple image adjustment data sets, evenwhen the signal is determined to be the same due to the frequency and form of the synchronization signal source.Use this when image adjustment (like aspect switching or white balance) is necessary due to the same signalsource.The sub-memory contains all data which can be adjusted for each signal, (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 45 45 On-screen display Input switching/Signal switching This displays the stored signal name for the STATUS screen during signal switching. Stored signal details RGB INPUT  No.：1 NAME : xxx60-A5-2ID : ALL SIGNAL STATUS NAME：xxx60-A5-2 MEMORY-No. ：A5-2 S.S.No. ：− INPUT No, ：1 fH ：48.30 kHz fV ：60.00 Hz SYNC STATE ：H(NEG) V(NEG) 75 ohm SUB MEMORY :  NAME ENTRY : ENTER EXIT (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 46 46 Using the RGB REALITY mode The RGB REALITY mode is a mode for converting RGB (primary color) input signals to component signals,performing high picture quality playback using image conversion processing specially for moving pictures.You can choose the RGB mode best suited for the type of RGB signals you are using (refer to page 40):RGB mode:  Choose this mode when the RGB signal source is a PC or other compu (...)

PTD9610U - DLP PROJECTOR Page 47 47 Adjusting the picture automatically The automatic adjustment (AUTO SETUP) is a function to automatically adjust the resolution, clock phase, andpicture position when inputting an analog RGB signal consisting of dots like a computer signal. (The input of amoving picture signal or any signal other than analog RGB signals cannot enable this function.)It is recommendable for the automatic adjustment to input a p (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 48 48 2. Special signal automatic adjustment Adjustment procedure Press the MENU button. ... The MENU screen will be displayed. Press the LEFT ( ) or RIGHT( ) arrow buttons once time. ... The AUTO SETUP MENU screen will be displayed. Press the LEFT ( ) and RIGHT( ) arrow to switch to desired MODE. •STANDARD ----- When receiving signals with an image aspect of 4:3 or 5:4•WIDE --------------When receiv (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 49 49 Signals which cannot be adjusted automatically should be adjusted manually. The following settings can beadjusted manually, and the respective adjustment procedures are given below. 1.Input signal resolution data2.Clock phase3.Picture position Adjustment procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP  ( ) and DOWN ( ) arrow buttons to select POSITION. Press the (...)

PTD9610U - DLP PROJECTOR Page 50 50 If a flicker or bleeding of the contour appears on the screen, adjust the clock phase to obtain an optimum picture. Adjustment procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP  ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed.Press the UP  ( ) and DOWN ( ) arrow buttons to select CL (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 51 51 Adjustment procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP  ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed.Press the UP  ( ) and DOWN ( ) arrow buttons to select SHIFT. Press the ENTER button. ... The SHIFT screen will be displayed.Press the UP, DOWN, LEFT and RIGHT ( , , and (...)

PTD9610U - DLP PROJECTOR Page 52 52 Adjusting the blanking Adjustment procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select BLK. Press the ENTER button. ... The BLK screen will be displayed.Press the control level buttons (  + (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 53 53 • If the black portions of the picture are fractured or tinged with green, adjust the clamp position its optimum state. Adjustment procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select CLA (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 54 54 • The KEYSTONE adjustment allows you to compensate for pictures’ horizontal trapezoidal distortion.  (Keystone adjustment can not carried out in built-in test pattern.) Adjustment procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed.Press (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 55 55 Adjusting the picture to the desired setting The following procedures can be used to adjust the picture to the desire appearance. Adjustment procedure ... Adjusting the COLOR setting Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select PICTURE. Press the ENTER button. ... The PICTURE screen will be displayed. Press the UP ( ) and DOWN ( (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 56 56 Adjusting the white balance (High / Low) Adjustment procedure  (Project a signal to be adjusted) Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select PICTURE. Press the ENTER button. ... The PICTURE screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select COLOR TEMP. Press the LEFT ( ) and RIGHT ( )&# (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 57 57 NOTE Adjusting the picture quality The following procedures can be used to adjust the picture quality to the desired setting. Adjustment procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select PICTURE. Press the ENTER button. ... The PICTURE screen will be displayed. • If a  or  indicator is shown at the bottom or top (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 58 58 • NR (noise reduction) settings cannot be adjusted for analog RGB input and TMDS input.• The FILTER adjustment is ineffective for XGA (1 024 x 768) mode on the PT-D9510U, or SXGA (1 280  x 1 024) mode on the PT-D9610U. It is also ineffective for any video input mode other than analog  RGB and TMDS modes, or if “THROUGH” is chosen for the SIZE mode (see pages 60 and 61). •&# (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 59 59 Adjusting the picture size Adjustment procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select SIZE. Press the ENTER button. ... The SIZE screen will be displayed.Press the control level buttons (&# (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 60 60 Screen examples for different size settings (For PT-D9510U) INPUT PICTURE Default Through H-Fit V-Fit HV-Fit 8 ：5 （640×400） 4 ：3 （1152×864） 5 ：4 （1280×1024） SIZESETTING The picture is displayed at  maximum size while maintaining  the original aspect. * If the picture extends outside the screen, the top-left corner is used as the reference point. (...)

PTD9610U - DLP PROJECTOR Page 61 61 Screen examples for different size settings (For PT-D9610U) INPUT PICTURE Default Through H-Fit V-Fit HV-Fit 8 ：5 （640×400） 4 ：3 （1152×864） 5 ：4 （1280×1024） SIZESETTING The picture is displayed at  maximum size while maintaining  the original aspect. * If the picture extends outside the screen, the top-left corner is used as the reference point. (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 62 62 Power up function The projector is provided with a power up function which allows the performance of the lamp to be utilized to themaximum level. Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select OPTION. Press the ENTER button. ... The OPTION screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select LAMP POWE (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 63 This equipment has 3 mode types for adjusting to the use environment. Switching procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select OPTION. Press the ENTER button. ... The OPTION screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select CONTRAST MODE. Press the LEFT ( ) and RIGHT ( ) arrow butt (...)

PTD9610U - DLP PROJECTOR Page 64 When receiving 480i with analog component signal YCbCr input, it is possible to switch Cb, Cr input. Switching procedure  Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select PICTURE. Press the ENTER button. ... The PICTURE screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select FORMAT. Press the LEFT ( )&# (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 65 65 Displaying a test pattern 17 types of test pattern are built in. These test patterns can be used to check the various adjustment settings.Use the following procedure to display a test pattern. •These test patterns cannot reflect the adjustment results of various picture settings such as picture quality, positions, and sizes. Be sure to project an external input signal for various adjustments.  Operating pr (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 66 66 Displaying the projector settings Display procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP  ( ) and DOWN ( ) arrow buttons to select OPTION. Press the ENTER button. ... The OPTION screen will be displayed.Press the UP  ( ) and DOWN ( ) arrow buttons to select  SYSTEM INFORMATION. Press the ENTER button. ... The SYSTEM INFORMATION screen will be (...)

PTD9610U - DLP PROJECTOR Page 67 67 Adjusting the edge blending Adjustment procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select EDGE BLENDING. Press the ENTER button. ... The EDGE BLENDING screen will be displayed.Press the UP ( ) (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 68 68 Adjusting the color matching The projector is equipped with color matching adjustment functions to adjust color balance when using severalunits in combination. Adjustment procedure  Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( ) arrow buttons to select PICTURE. Press the ENTER button. ... The PICTURE screen will be displayed. Press the UP ( ) and DOW (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 69 69 This projector is provided with an ID number function, so that if multiple projectors are being used together, theprojectors can be controlled all at once or separately using a single remote control unit.Because the factory pre-setting of the ID number is ALL, using only one projector do not require this setting. Setting ID numbers Setting procedure Press the MENU button. ... The MENU screen will be displayed.Pre (...)

PTD9610U - DLP PROJECTOR Page 70 70 Setting remote control unit ID numbers When an ID number has been assigned for a projector, you then need to assign the same ID number as theprojectors to be controlled to the remote control unit which is to be used to operate these projectors, otherwise theremote control unit cannot be used.Because the factory pre-setting of the projector ID number is ALL, using only one projector requires the use of theID ALL b (...)

PTD9610U - DLP PROJECTOR Page 71 71 Using the RS-232C connectors The projector is equipped with a D-SUB 9-pin RS-232C input connector and RS-232C output connector whichallow the projector to be controlled externally. These connectors conform to RS-232C specifications, and can beused by a computer which conforms to either RS-232 or RS-232C specifications. • Set the communication parameters below according to a computer to be connected. To con (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 72 72 Using the RS-232C connectors (continued) ID List ID       Code specified ALL        00h 1            01h 2            02h 3            03h 4            04h 5            05h 6            06h 7  (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 73 73 RS-232C settings Setting procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP ( ) and DOWN ( )  arrow buttons to select OPTION. Press the ENTER button. ... The OPTION screen will be displayed.Press the UP ( ) and DOWN ( )  arrow buttons to select RS-232C SETTING. Press the ENTER button. ... The RS-232C SETTING screen will be displayed.Press the UP ( ) and DO (...)

PTD9610U - DLP PROJECTOR Page 74 74 Using the RS-232C connectors (continued) List of basic control commands CODE Target remote control buttons  NAME 06h RGB 0Ah INPUT1 0Bh INPUT2 0Ch INPUT3 0Fh NEXT 10h 1 11h 2 12h 3 13h 4 14h 5 15h 6 16h 7 17h 8 18h 9 19h 0 35h BRIGHT 36h CONTRAST 3Bh STD 3Dh POWER 3Eh POWER ON     *2 3Fh POWER OFF *2 40h TEST *2 58h + 59h − 5Ah5Bh5Ch5Dh 62h ON SCREEN 6Bh ID ALL   *1 6Ch ID SELECT   (...)

PTD9610U - DLP PROJECTOR Page 75 75 Selecting the RS-422 Serial Interface Refit the  CPU module. Plug the projector into the wall outlet and set the front MAIN POWER switch to ON.Check that the LED to the left of the RS-232C-IN port is lit red. CM Remove the connector that connects CM5 to CM6, then use the same connector to connectCM6 to CM7. Converting the RS-232C-IN port into an RS-422-IN port If the projector power is ON, turn it OFF by pre (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 76 76 Refit the  CPU module. Plug the projector into the wall outlet and set the front MAIN POWER switch to ON.Check that the LED to the left of the RS-232C-OUT port is lit red. CM Restoring the original RS-232C-OUT port function If the projector power is ON, turn it OFF by pressing the remote-control (or on the projector)POWER key, and wait for approximately 5 minutes until the cooling fan stops. Set the fro (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 77 77 Using the network module The network module for this unit has a LAN interface, so the unit can be controlled from the web browser of a PC.The network module has an automatic send function for e-mail. Mail can be sent to a previously set e-mail address when a problem occurs, or when the set value for the lamp usage time is attained. Connection example A LAN cable is necessary when using the network module. Hu (...)

PTD9610U - DLP PROJECTOR Page 78 78 Operating procedure Press the MENU button. ... The MENU screen will be displayed.Press the UP  ( ) and DOWN ( ) arrow buttons to select OPTION. Press the ENTER button. ... The OPTION screen will be displayed.Press the UP  ( ) and DOWN ( ) arrow buttons to select  NETWORK MODULE SETTING. Press the ENTER button. ... NETWORK MODULE SETTING screen will bedisplayed.Press the UP   (...)

PTD9610U - DLP PROJECTOR Page 79 79 Item Function Description HOSTNAME DHCP IP ADDR NET MASK GATEWAY MAC ADDR Change if necessary when using a DHCP server etc. Turn the DHCP item ON when automatically obtaining IP addresses using a DHCP server. Turn it OFF whennot using a DHCP server. Input an IP address when not using a DHCP server. Input the net mask when not using a DHCP server. Input a gateway address when not using a DHCP server. This dis (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 80 80 Accessing from a web browser Go to: 192.168.0.8 Start up the PC’s web browser. Input the IP address set on the unit in the URL input field of the web browser.Input user1 in the user name field, and input panasonic (lower case letters) in the password field. When OK is pressed, the top page is displayed. Username and Password Required Enter username for Panasonic Projector Control at192.168.0.8 Cancel User (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 81 81 Top page    TOP-Panasonic projector control window - Netscape File    Edit    View    Go    Window    Help Copyright (C) 2001 Matsushita Electric Industrial Co., Ltd. Projector control window Power status  OFF Document Done Initial set up Projector control Status information E-mail set up Projector firmware up date Option Update button Clicking on t (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 82 82 Network setting page Select ON to activateDHCP client function Input IP address when not using DHCP server Input port number.Normally, this is usedwith the default 80. Input net mask whennot using DHCP server Input gate addresswhen not using DHCPserver Input projector name.Input the host name, ifnecessary, when usingDHCP server etc. Projector control page This displays theprojector state. This displays theproject (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 83 83 Status display page Displays input slot status Displays projectorinternal temperature Displays projectorexhaust temperature Displays lampillumination remainingtime Displays projectoroperation time Displays self-diagnosisinformation Displays firmwareversion of projector mainunit Displays projector type. (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 84 84 E-mail setting page • This enables automatic sending of mail to up to two mail addresses. When using the e-mailfunction, select Enable. Input the IP address ofthe e-mail server (SMTP). Data such as the set-uplocation of the projector can beinput so it is easy tounderstand where the e-mailcame from. Input the e-mail address ofthe projector. The minimum timeinterval for temperaturewarning mail can bechanged. (...)

PTD9610U - DLP PROJECTOR Page 85 85 E-mail setting page (continue) When using two e-mailaddresses, input the e-mailaddress to send mail to. After all input is finished, pressthe Submit button. Select the conditions for sending e-mail Error: When an error occurs in self-diagnosisWarning LAMP1: When the lamp illumination remaining time reaches  the time set in the column on the right side. Warning LAMP2: When the lamp illumination remaining time (...)

PTD9610U - DLP PROJECTOR Page 86 86 Firmware update page(Firmware updating should only be done by a person with specialized knowledge.) • When rewriting is finished, this message is displayed. After inputting the file name, pressthe upload button. Transfer will begin.It takes a few tens of seconds fortransfer to occur. The time variesdepending on the network situation. Input the file name of the firmware tobe updated. Displays the current ve (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 87 87 • If too much dust accumulates on the air filter, the temperature inside the projector will rise and may cause the  power to turn off. Clean the air filter approximately every 500 hours of use (varies with the environment in which the projector is used). Cleaning the air filter Consult a service technician to  clean or replace the air filter. CAUTION Returning the network module settings to (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 88 88 Notes on handling the lamp unit • The lamp unit is sold separately and consult a Panasonic authorized dealer or service center.  Part No. :  ET-LAD9610 Lamp unit replacement period The life span of this lamp unit is 1 500 hours maximum, after which it will need replacing (recommendedreplacement time is 1 000 hours). in the normal usage mode. The operating life of the lamp also depends on thenumbe (...)

PTD9610U - DLP PROJECTOR Page 89 89 Before asking for service, check the following points. Power does  not turn on. No picture  appears. Color is misaligned  when special signals are input. The contrast and  brightness of the picture cannot be adjusted • Is the power turned on at the  power point? • Is the power cord disconnected  from the power point? • Is the MAIN POWER switch  (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 90 90 Specifications PT-D9510U PT-D9610U (PT-D9510U) (PT-D9610U) PT-D9510U PT-D9610U 200 V – 240 V AC (single-phase, 3-wire), 14 A (Max.)2.2 kWApprox. 13 W during standby (when cooling fan is stopped) 0  °C – 40 °C : NORMAL lamp power 0  °C – 35 °C : HIGH lamp power  If the power is turned on when the temperature is around 0  °C, a warming-up time&# (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 91 91 Accessories • Remote control unit  • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 1 • AA-size batteries   • • •  (...)

PTD9610U - DLP PROJECTOR Page 92 92 Sold separately Select from the range available in accordance with the setting-up location and system requirements. ※ ※ Refer to the ET-D95LE9 operating instructions when installing. NAME MODEL   NO. Projectionl e n s e s M o d u l e s O t h e r Zoom lens 1.5 – 2.5 : 1 Zoom lens 2.5 – 4.0 : 1 Zoom lens 4.0& (...)

PTD9610U - DLP PROJECTOR Page 93 93 UNIT : mm (inch) Dimensions 960(37.8") 428(16.8") 680(26.8") 753(29.6") 604(23.8") 1051(41.4") 712(28") 169(6.7") 114(4.5") 13(0.5") φ 29(1.1") 332(13.1") φ50(2") (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 94 94 NOTES IMPORTANTES CONCERNANT LA SÉCURITÉ AVERTISSEMENT: Afin d’éviter des dommages qui risquent de causer un incendie ou des chocs électriques,   ne pas exposer cet appareil à la pluie ou à l’humidité. Alimentation: Ce projecteur DLP a été conçu pour fonctionner seulement sur secteur domestique de                (...)

PTD9610U - DLP PROJECTOR Page 95 95 Précautions concernant la sécurité Lire attentivement ce mode d'emploi et respecter toutes les précautions de sécurité indiquéeslors de l'installation du projecteur, afin d'éviter des accidents. AVERTISSEMENT Installation Confier l'installation du projecteur à un technicien qualifié seulement. •Afin de garantir une installation sûre et précise, il faut confier ce travail à& (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 96 96 Lors de l'utilisation du projecteur Ne pas regarder directement dans la lentille pendant que le projecteur fonctionne. • Une lumière intense est émise par la lentille du projecteur. Si l'on regarde directement dans cette lumière, elle risquerait de blesser et d'abîmer les yeux. Ne pas placer le projecteur sur des surfaces inclinées ou instables. • Le projecteur risquerait de tomber ou de s (...)

Panasonic PTD9610U - DLP PROJECTOR Manual Page 97 97 Précautions à suivre lors de la manipulation PRÉCAUTION Installation Toujours respecter les points suivants lors de l'installation du projecteur. Une alimentation électrique spécialisée doit être utilisée. • Demander à son revendeur d'effectuer les travaux d'électricité qui peuvent être nécessaires pour fournir une alimentation électrique de 14 A, (...)

Panasonic PTD9610U - DLP PROJECTOR Projector Manual Page 98 98 Remarques concernant l'utilisation Afin d'obtenir la meilleure qualité possible d'image • Si la lumière du jour ou la lumière intérieure éclaire l'écran, les images projetées n'auront pas le contraste adéquat. Fermer les rideaux ou les volets des fenêtres, éteindre les éclairages fluorescents près de l'écran etcouvrir tout plancher ou mur à haute réflexion de ta (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 99 99 Remplacement du module-lampe Remarques concernant la manipulation du module-lampe • Le module-lampe est vendu séparément, adressez-vous à un détaillant Panasonic agréé ou à un centre de service Panasonic.  Numéro de pièce: ET-LAD9610 Période de remplacement du module-lampe La durée de vie de cette lampe est de 1 500 heures maximum, après lesquelles vous devez la re (...)

Panasonic PTD9610U - DLP PROJECTOR Operating instructions manual Page 100 Panasonic Broadcast & Digital Systems CompanyDivision of Matsushita Electric Corporation of AmericaExecutive Office: 3330 Cahuenga Blvd W., Los Angels, CA 90068 (323) 436-3500 EASTERN ZONE: One Panasonic Way 4E-7 Secaucus, NJ 07094 (201) 348-7621 Mid-Atlantic/New England : One Panasonic Way 4E-7 Secaucus, NJ 07094 (201) 348-7621Southeast Region: 1225 Northbrook Parkway, Ste 1-160 Suwanee GA 30024 (770) 338 (...)